Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
The article author is making several good pointers on How to Install a Bathtub in general in the article down below.
Mounting a tub isn't exactly brain surgery, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately difficult project. If the old bathtub is easily available, the task can move speedily; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the brand-new one. See to it you have actually certified on your own for the task as well as fit attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is far better to take into consideration using one prior to you begin. Opportunities are you might require a specialist plumber to make tube connections.
This article will certainly aid you mount a new bathtub in your washroom if you have actually already purchased a brand-new bathtub as well as don't require to transform the arrangement of your previous water system pipelines.
Your devices and also product checklist should make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, then the first thing you need to do is detach the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of removing the existing faucets can be rather troublesome as a result of the restricted gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a towel ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have been removed, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Before proceeding to fit the new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in area between the faucet and also the sink. Protect the faucet in position with the producer given backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type should be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the required position. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the tub until the level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water and inspect all joints and new pipework for leaks and tighten them if required. Fill up the bathtub as well as also check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, take care of the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the bathtub should wait up until the bathtub has actually been made use of a minimum of when as this will certainly settle it into its final position.
Getting ready for the Setup
To start with, the sustaining framework provided with the bath ought to be fitted (if called for) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in difficulties with dampness as well as possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealant can break rather early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the market. It is advisable to fit the tiles making use of water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about Installing A Bathtub? Try leaving a remark below. We would be interested to listen to your opinion about this entry. We are looking forward that you visit us again in the future. Kindly set aside a second to share this post if you appreciated it. Thank you for your time. Visit us again soon.
Click On This Link Report this page